Why Servo Instead of DC Motor? Robotics?

Why do people use servo instead of DC motor?.. The accurate answer is, it all depends on the application that the motor's controlling. For example, you need the robotic arm to move at a precise angle of 37degrees..than servo motor is the one. If you only want the robotic arm to just rotate then use DC motor.. Angle controlling can be done in 2 ways, by using servo motor or stepper motor..but typically eople would go for servo as it give more accurate output. To understand how servo works is something that is hard to explain here at Y!A because of the limitation of space to write, so, you can google PWM = Pulse Width Modulation..that will give you the general idea of how servo works.. p:s/ if u need more explanation on servo, feel free to email me.

1. 56 to 15 Volts Regulator for DC Motor Driving

I planned to drive gate with 100 ohm resistor in order to reduce driving current and reduce the power loss along the lm2576.A MOSFET gate is a capacitor: to turn the FET on, a certain amount of charge must be pushed into the gate, this is called Qg or total gate charge.The output current capability of the driver only changes how long it takes to push Qg into the gate. For example with your Qg=130nC MOSFET, at 1A drive it would switch in 130ns, and at 0.1A drive it would switch in 1.3s.Once the FET is turned on, the driver only consumes its idle current, which is listed as "Quiescent VCC supply current" in the datasheet, and the maximum is 340A, which is tiny.Thus, gate drive current only influences switching speed (and MOSFET switching losses) but has almost no influence on the current used by the MOSFET driver. This current can be estimated as:$ Frequency * Qg * 2 $Since there are two FETs, it will use the above amount of charge (coulombs) per second, and since current is coulombs/s, you have your current.For 25kHz and 130nC it will be about 6.5mA. Size it up for 10mA maximum, you will be fine.(also your IR2106 wo not work without the bootstrap caps and diode). In fact, the gate drive current should be chosen to make the FETs switch as fast as necessary to keep switching losses down, but not faster, as this increases EMI

2. RS-550 DC motor controller 24V (35-70) A working range and a stall of 120A

How soon is this robotics challenge? Unless it's sometime in 2025 I can tell you from experience that you probably are not going to be able to build one in time. People that understand how to drive high power MOSFETS at high frequencies do not seem to want to share their knowledge. Go buy a Sabertooth 2x50 from Dimension Engineering and be done with it.

3. rotating a dc motor one direction then the other with a single power source?

much easier to do with one pushbutton and a DPDT switch to reverse direction. But it can be done with two double pole pushbuttons. the problem is that if you push both at the same time you will short out your power supply and blow fuses. And ruin the pushbuttons. Edit: you can fix this by adding four diodes in the proper places. You can also use 2 single pole pushbuttons and two relays. And a "chip out of a joystick" wo not do any motor switching.

4. Is there any DC motor produces 7000 RPM and 100 HP,if so then what will be the input volt and wattage?

Since it used on a car then there is no reason for specifying 7000 RPM which needs lots of gearing to be stepped down

5. Hooking a 12v DC motor directly to GPIO 5v , possible? [closed]

All the Pi's GPIO are 3V3 and can only supply a few milliamps, not enough to power your motor.Even if the GPIO could supply enough power it would be damaging to connect a motor direct to the Pi. The back EMF from the motor as it is switched off could destroy the Pi/GPIO. The 5V pins on the expansion header are not GPIO, they are not switchable. They are always "on" while power is applied to the Pi.You can buy a motor driver board for a few UK pounds from eBay, e. g. look for L9110S and L298N boards. That would be the "correct" way to control a motor from the Pi.It would be sensible to use an external power supply to power the motor. In that case you still need to join the Pi ground with the power supply ground.

hot searches
36V Li-ion battery 3 positon Cordless Scarifier/Aerator with quick change knob 3000w Electric Leaf Aspirator Blower 8000-15000rpm Electric Leaf Blower 270km/h Leaf Blower 15KW New bestselling best price Kerosene heater with outdoor use 600W high quality Electric Hedge Trimmer with two safety switch10 1200w Miter table Saw with 210 Max cutting Mitre Saw with upper table 20V Cordless Pruner Pole Chain Saw With Adjustable Head with cheap price factory 510mm balde length Electric hand Hedge Trimmer machine with 600W Rated power 25mm high pressure power dirty water pump garden clean machine 43CC Petrol Gasoline blower Electric Corded Miter table Saw with cheap price
Artikel panas
What Led to Racial Relations Being Better in Namibia and Botswana, Compared to South Africa?
Is there anyone recovered from covid-19? Can you share your hospital bills?
Which would win, a Landkreuser P 1000 Ratte and Maus tank or a Bob Semple tank?
UNICAR Guatemala, the Aortic Valve Replacement Hospital in Guatemala City
A poultry farmer collects eggs every morning. There are 50 broken eggs per collection on average. What is the probability that more than 60 eggs might be
Chinese Government Assists Dominica with 2,500 Solar Street Light with Battery and Panel
Is There a Reason That I Need a HUD App'd Water Heater Or a Special Water Heater for a Mobile Home/t
Why did you learn Machine Learning?
Rite Academy Hyderabad Best Institute for NDT
Farm Machinery in Ethiopia Bolstering the Agricultural Backbone
dc motor related articles
Tips to Help You Design the Perfect Solar Battery for That Party
Functional Features and Application Introduction of TG452 Series Intelligent Street Lamp Gateway
What Is the Best the Best Solar Street Light for You? - the Best Solar Street Light Reviews
IGBT of Fuji Motor Electronic Equipment Technology
Is a Metal Roof Right for You | Billy

Copyright © 2020  Shandong Abusair Agricultural Machinery Co,. Ltd- |  Sitemap

Multifunctional farm Abusair machinery  |  Tea Professional Cultivator farm machinery